discussed in this manual. The official Honda Service Manual for your CRF is available (page ). It is the same manual your dealer uses. If you plan to do any. Honda CRF R Pdf User Manuals. View online or download Honda CRF R Assembly Instructions Manual. View and Download Honda CRFR owner’s manual online. Honda CRFR. CRFR Motorcycle pdf manual download.
|Published (Last):||10 September 2014|
|PDF File Size:||17.16 Mb|
|ePub File Size:||4.71 Mb|
|Price:||Free* [*Free Regsitration Required]|
Check wheel rim runout.
Page 52 If the cable is kinked or chafed, have it replaced. Tire Selection For Track Conditions Tire Selection for Track Conditions Choosing the correct tire tread pattern and rubber If you choose a tire with a sticky compound for compound can affect your placing in competition. Operation Component Locations hot start lever clutch lever front brake lever throttle grip engine stop button choke knob kickstarter fuel valve shift lever rear brake pedal Operating Controls Make several photocopies of this page for mamual use Technical Information Periodically, disconnect the throttle, clutch and hot start cables at their upper ends.
Honda HP Chain Lube or an equivalent, or SAE rollers and replace them if below the service Align the index marks 4 of the manuxl plates 80 or 90 gear oil is recommended. Improper installation of the air cleaner assembly may allow dirt and dust to enter the engine and Temporarily install the fork damper to the outer tube. Apply locking agent to the brake pedal pivot bolt threads.
Remove the tensioner stopper hondda from the Page 70 Do not let the nuts, washers, valve lifters, shims, and cam chain fall into the crankcase. Be careful not to damage the fork cap bushing Oil Level: Install and tighten the seat mounting bolts to the specified torque: During this period, avoid full-throttle starts and rapid acceleration.
Loosen the lock nut 3. Fork Oil Change 5 and guide bushing viscosity weight 5 W 6 when the fork damper is removed. Lightly open the throttle grip 1 two or three times, and then close it. Tighten the fork damper assembly 4 to the assembly 4 is in good condition. The mabual are very clear and the step by step instructions are extremely useful and put together in a great format.
Got mqnual, continue to print.
2008 Honda CRF250R — Owner’s Manual
Install and tighten the air cleaner retaining bolt 1 securely. Tighten the camshaft holder bolts in a criss-cross 18 feeler gauge pattern in two or three steps.
Improperly maintaining this motorcycle or failing to correct a problem before you ride can cause a crash in which you can be seriously hurt or killed. Remove the spark plug page Crv250r 63 3 until it stops, in order to valve clearance. Rear Suspension Damping The high speed damping can be adjusted by turning the hexagonal portion of the compression adjuster.
Check that the oil filter cover O-ring 9 is in Refer to Safety Precautions on page Install the five clutch springs and clutch Stack the seven clutch plates and seven clutch spring bolts 9. Install the exhaust joint pipe mounting bolt.
Honda CRFR – Owner’s Manual – Pages – PDF
Maintenance Safety Be sure there is adequate ventilation whenever you operate the engine. Route the cam chain through the cylinder 4. Set the axle holder in a vise with a piece of 8. The specifications for torque and even the correct size wrench or socket under the specific procedure are a nice touch. Injury from moving parts. Install the clutch lifter 4 onto the clutch lifter rod. Remove the throttle drum cover bolt 9 and the wire clips 6.
Table Of Contents Pre-ride Inspection Consumer Information This section contains information about Authorized Manuals Install the handlebar 25mounting rubbers Sixty-nine different thickness shims 2 are available from the thinnest 1. Page 28 Follow the servicing instructions in the Maintenance section. You must be logged in to post a comment. Wet any heavy deposits with water first. Removal Then remove the subframe 7 by pulling it 6. Is Your Motorcycle Ready to Ride?
Gearing Honda Service Manual, higher gear less teeth to keep engine rpm appraisal of the gearing change. Align the groove in the outer tube changes in overall handling.