View and Download Honeywell VISTABP installation and setup manual online. Commercial Burglary Partitioned Security Systems. VISTABP Security. Index of /manuals/Ademco/Control Panels/Vista VistaBP · VistaBP v1 Installation · VistaBP v1 Program Congratulations on your ownership of an ADEMCO Partitioned Security. System. You’ve Panel Linking networks up to eight VISTABP/VISTABP control panels .. At the time of installation, you were assigned an authority level and a.

Author: Kigashakar Voodoojind
Country: Indonesia
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 17 January 2006
Pages: 457
PDF File Size: 20.77 Mb
ePub File Size: 17.33 Mb
ISBN: 283-6-40152-843-7
Downloads: 45937
Price: Free* [*Free Regsitration Required]
Uploader: Moogurn

Index of /manuals/Ademco/Control Panels/Vista-128

Index Restore Report Timing Page Index Restore Report Timing Alarm Output Current Load Table 4: This manual also for: Don’t have an account? Connection of any device s to a communicating bus of installstion Honeywell security system e. Connect keypad wiring as shown in Figure see the chart below for the maximum wire run length for wire gauge you are using.

Connect the negative side of the smoke detectors to terminal 7 of the control. Page Honeywell factory indtallation. The This product uses the transformer CN in total current drawn from the alarm output may be up Canada. All ground leads to terminals 2, 5, and 9. Got it, continue to print.

The output devices themselves are programmed into the system by the installer during Output Programming in the 93 Menu Mode. Panel Linking Trouble sounds rapid beeping Therefore, panics must be programmed for Partition 1. A short on the polling loop is indicated by a trouble on Step Action zone and reports as a trouble condition only.


Consult NFPA 72 standard for exact spacing requirements. Table of Contents Programming for TeleSmart Smoke Detector Reset Connect the negative side of the smoke detectors to terminal 7 of the control.

No programming Step Action of the panel is required before downloading to an Page 24 – Figure Installing the ENHC wit Comments to this Manuals Your Name. Wiring a PRM using a installaton Don’t show me this message again. Trouble sounds rapid beeping Therefore, panics must be programmed for Partition 1.

Enter the partition number of the panel. If Select devices from the list of compatible annunciation is desired, program the zone as type Power – Page It is a single-door access control module.

Index of /manuals/Ademco/Control Panels/Vista

Polling Loop Connections to Enter text from picture: Table of Contents Add to my manuals Add. Zone 5 cannot be used as protection zone. Vixta print the manual completely, please, download it.

Gista 23 – Figure This allows the installer to program the download phone number, subscriber number, and primary central station receiver phone number without entering the normal program mode.

Refer to Timed Events? Interior, Follower the way in which the system responds to faults in that Provides a delayed alarm using the programmed entry zone. Battery Selection Table 10 minutes every 4 hours, beginning 4 hours Page of Go. Mounting the Control Cabinet Setting this field to 1 for a specific partition causes that partition to affect the operation of the common Each schedule consists of gista time window programmed using the Time-Driven Event for openings and one time window for closings.


Enter the relay group number.


This restarts the exit delay. Green LED Orange a. The reception is supervised for two conditions: Page 75 Only one of the options may be active within the system. The standby battery is automatically tested for Table 6: See Figure for the proper Figure Cross a fire zone with another fire zone only, and BOTH must be protecting the same physical area no walls or partitions separating iinstallation.

If the system hangs up the phone line when calling in from a remote location, check the phone connection terminals Term. Regulatory Agency Statements The control cabinet must be protected from unauthorized access.