Visit our website and learn more about AS/NZS standards. AS/NZS Regulatory compliance mark for electrical and electronic equipment – Specific requirements for particular regulatory requirements. Shown in the AS/NZS as the relevant standard that can be readily applied to the equipment type or;; Is accepted by the electrical safety regulator as a.

Author: Vudogis Yozshuramar
Country: Saint Kitts and Nevis
Language: English (Spanish)
Genre: Spiritual
Published (Last): 18 November 2011
Pages: 475
PDF File Size: 7.77 Mb
ePub File Size: 13.52 Mb
ISBN: 378-1-47457-393-7
Downloads: 96318
Price: Free* [*Free Regsitration Required]
Uploader: Akinorn

Solar Accreditation – Update: Prescribed electrical equipment – DC isolators

Specifies the requirements for the use of a trademark, called the Regulatory Compliance Mark RCMon electrical and electronic products to az compliance with regulations applicable to aspects of the product as covered in other parts of this Standard.

Solar installations in NSW are not affected at this stage. Description You are required to comply with this standard if you intend to sell electrical articles. Solar installations in NT are not affected at this stage. At present DC isolators have not been gazetted as a prescribed article level 3. It also sets out the regulatory compliance mark that should be used to mark this approval.

AS/NZS – Standards Australia

If you have any queries or require any aw information, you can contact ESV’s Electrical Equipment Safety team on 03and select option 2. The following table shows the basic requirements that are applicable. Existing jzs already in Australia prior 30th June is considered Ass level 1 and can continue being sold until 30 June provided the responsible supplier is registered. Consumer, Building and Occupational Services Opens in new window. By Admin July 16, As such, existing stock can be sold out over the next 12 months.

The electrical equipment safety system EESS legislation, which is currently before the Victorian Parliament’s Legislative Council, means that there is currently no requirement for supplier registration or equipment registration in order to supply DC isolators in Victoria.

It is an offence under section 57 of the Act to supply Level 3 or prescribed electrical equipment that has not been approved by ESV, another electrical safety state nss or JAS-ANZ accredited third party certifier. The closing date for comment on these draft standards is 7 September The Standard was prepared in response to a proposal from the Electrical Regulatory Authorities Coordinating Committee. Follow Us facebook linkedin youtube. Installer Sign In Search Search for.

Standards Catalogue

Of particular importance to the industry, DC isolators will now be classified as a level 3 prescribed item. To obtain a certificate, the products must comply with one of the following: Home Products DC isolators update. Nxs part of the Standard deals with electrical safety regulations in Australia and New Zealand. Code of Practice A code of practice is ax set of rules which details how people in a certain industry should behave.

  MAKATON CORE VOCABULARY PDF

We have noted considerable confusion and frustration today within the solar industry regarding the issue of appropriately-certified DC isolators. Energy Safe Victoria ESV expects suppliers who hold a voluntary certificate of suitability for their DC isolator to work with their certifier to obtain a valid certificate of approval. ESV has prioritised the processing of these applications.

This issue affects the installation of household solar power systems in some states and we are conscious that it needs to be addressed quickly. The Clean Energy Council welcomes improvements to safety outcomes but we are concerned about the way this is being implemented in some states, and believe a longer transition period is required. Section 57 of the Act does not provide ESV with an exemption power however; ESV will not immediately strictly enforce the new requirements against installers or suppliers of DC isolators.

You are required to comply with this standard if you intend to sell electrical articles.

This Part of the Standard deals with the use of the Regulatory Compliance Mark to indicate that a piece of radio apparatus complies with the relevant radio apparatus regulations in Australia nza New Zealand. For electrical equipment that is required to be approved by regulators before being placed on the market declared articlesthere are specific regulatory requirements additional to the general requirements given in this Standard. Clean Energy Council Insulation Accreditation. New products manufactured in Australia or imported into Queensland after the 30 Junemust comply with the requirements of In-Scope Level 3.

The requirements are now fully harmonized. This standard sets out the kind of electrical articles that 44177.2 approval. It is understood that electrical regulators will continue to accept such marking 441.72 a period, in nsz with the use of the RCM.

These regulations are undergoing a transition both in the means by which compliance is demonstrated, and in terms of harmonization between Australia and Nze Zealand. There are a number of ways for suppliers to get mzs product certified. Main Content Clean Energy Council. Any new product types sourced by an importer would need to comply with level 3 requirements. To obtain a certificate, the products must comply with one of the following:.

  GACETA OFICIAL 5890 PDF

Please consult the Contact Officer for more information and to ascertain the level of compliance that may be required. Northern Territory Solar installations in NT are not affected at this stage. In some situations, this may be purely an administrative process however in other situations further technical documentation may be required. A code of practice is a set of rules which details how people in a certain industry should behave. Contact Email, Phone and Address Details for this service in simple two column table format, header then data.

There are also currently nzd applications for approval of DC isolators currently with ESV for assessment however, further technical documentation is required to be provided by the applicants in order to progress and finalise those approval applications. Victoria Refer to the updated information above.

Under the EESS, there is nzss section in the Regulation which effectively states that existing stock which was imported as level 1 equipment will be continued to be treated as level 1 equipment for 12 months from the date the reclassification came into effect. Tasmania Refer to the updated information above. Products that have been certified and can be supplied in Victoria can be found in the following register https: To date in Australia, marking of products with the number of the certificate of approval or certificate of suitability has been the usual means of indicating compliance.

This part of the Standard deals with electromagnetic compatibility regulatory requirements in Australia and New Zealand.

The objective of this Standard is to provide a set of outcomes-oriented criteria for the safety of electrical equipment, primarily for use by electrical regulators in relation to products for which regulatory approval before sale is not required non-declared articles.

To date, ESV has taken an 447.2 approach to the supply of unapproved DC isolators into the Victorian market provided installers made every effort to source and install approved DC isolators, and that suppliers of DC isolators were in a genuine process of obtaining approval of their product. In most states, it is an offence to supply level 3 or prescribed electrical equipment without being approved by a state electrical safety regulator or a JAS-ANZ accredited third party certifier.