ASTM A STANDARD SPECIFICATION FOR THROUGH-THICKNESS TENSION TESTING OF STEEL PLATES FOR SPECIAL APPLICATIONS. ASTM A A M – Designation: A /AM – 03 Standard Speci? cation for Through-Thicknes. copy of ASTM A is included in Appendix A of this report. In the process of . of a rolled W-shape that is made of ASTM A Grade 50 steel.
|Published (Last):||18 March 2012|
|PDF File Size:||9.44 Mb|
|ePub File Size:||2.91 Mb|
|Price:||Free* [*Free Regsitration Required]|
ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
Posting Guidelines Promoting, selling, recruiting, coursework and thesis posting is forbidden. This documents may be applied as a supplement to all product standards for flat products and sections of fully killed steel, except stainless steel.
Thank you for helping keep Eng-Tips Forums free from inappropriate posts. Within the text, the SI units are shown in brackets.
The number of tests and test positions have not been established that would provide a good estimate of both the mean and the variability of through-thickness tensile reduction of values of a plate.
Further strain can cause the remaining metallic ligaments to shear or rupture, resulting in the step-like fracture appearance. For example, those nonmetallic inclusions that form during the solidi? See Test Methods and De? Lamellar tearing may also w770 from loads on the plate surface. Link to Active This link will always route to the current Active version of the standard.
It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. Digital Transformation may be defined in a number of different ways by analysts or enterprise software vendors.
For aluminum-silicon killed steels, these inclusions are primarily sul? Download Now Defense manufacturing is all about project manufacturing and project accounting. Red Flag This Post A770 let us know here why this post aztm inappropriate. However, lamellar tearing is not w770 con?
This scatter of aastm results is due in part to the inherent variability of the distribution of the nonmetallic inclusions discussed in X1. Shielded metal arc, friction, stud, or electron-beam welding methods have proven to be suitable. Take the test coupons from the center of the a7770 width.
Operator technique will also be a factor in increasing scatter, particularly in the measurement of the? The number of tests required will depend upon the thickness of the plate being tested and the reduced section length selected.
ASTM A770/A770M – 03(2012)E1
For plates over 41? In silicon semikilled or fully killed steels, these inclusions are primarily oxides present as silicates and sul? Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. The tearing may remain completely subsurface or axtm at plate edges or at weld toes. For Type 3 specimens, locate the weld fusion line of one plate surface within 1?
The tension testing method shall provide a measure of the resistance of a steel plate to lamellar tearing. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.
A minimum slenderness ratio a7700 2. This minimum value may be from 1.
Athough thickness tension test – ASTM (testing materials) Code Issues – Eng-Tips
However, A is not clear in scope. This standard has been approved for use by agencies of the Department of Defense. Are you an Engineering professional? The potential variability of the test results also increases the possibility that subsequent astmm of a steel plate quali? Within the plate thickness dimension speci? The tests shall be representative of the plate in its? The Type B specimen provides a reduced section length of 21?
It does not refer to the condition of the plate. Combining values from the two systems may result in nonconformance with the specification. Reduction of Area Requirements S3. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.
ASTM A A M_百度文库
To provide a high resistance to lamellar tearing may require the use of special steel-making processes that can reduce the oxygen and sulfur contents in the steel to very low levels. Below this minimum value, the reduction at the failure point in wstm reduced section is restrained by the larger cross section away from the reduced section.
Join your peers on the Internet’s largest technical engineering professional community. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.