ASTM E Liquid Penetrant Equivalent 23rd May , AM ASTM E , Standard Practice for Liquid Penetrant Examination for General Industry. ASTM E Standard Practice for Liquid Penetrant Examination; ASTM E Standard Practice for Visible Penetrant Testing Using Solvent Removable. Aug 9, For those of you who do liquid penetrant testing, you’ll want to know that there’s a new Edition of the ASTM E/EM standard.

Author: Fauk Kazraktilar
Country: Latvia
Language: English (Spanish)
Genre: Technology
Published (Last): 15 May 2008
Pages: 193
PDF File Size: 1.91 Mb
ePub File Size: 14.94 Mb
ISBN: 647-3-26122-833-2
Downloads: 25264
Price: Free* [*Free Regsitration Required]
Uploader: Maushakar

Satisfactory inspection results can usually be obtained on surfaces in the as-welded, as-rolled, as-cast, as-forged, or ceramics in the densi? If sample adjustments are made, adjust standards and blanks identically.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

A developer is applied to draw the entrapped penetrant out of the discontinuity and stain the developer. NOTE 8—Surface preparation of structural or electronic ceramics for penetrant testing by grinding, sand blasting and etching is not recommended because of the potential for damage. A test piece containing one or more discontinuities of the smallest relevant size is generally used.

Because of the short contact time, degreasing may not completely clean out deep discontinuities and a subsequent solvent soak is recommended. The method is applicable only to materials that are totally combustible.

Tag: ASTM E165-09

Care should be taken to only use bulbs suitable for? For immersion rinsing, parts are completely immersed in the water bath with air or mechanical agitation. The full amount of these elements will not be reported.

Aqueous developers shall be applied to the part immediately after the excess penetrant has been removed and prior to drying. Solvent-type paint removers can be of the high-viscosity thickened type for spray or brush application or can be of low viscosity two-layer type for dip-tank application.

  DEDES IR DEDIENES PDF

It should be asym out, however, that after indications have been found, they must be interpreted or classified and then evaluated. Some penetrant materials contain signi? Adjust detector offset to zero-out eluant conductivity; with the? Other materials may contain impurities, which are not volatile and may d165-09 with the part, particularly in the presence of moisture or elevated temperatures. Subtract the second reading from the? Cool and dilute to 1 L. The length of time the penetrant must remain on the part to allow proper penetration should be as recommended by the penetrant manufacturer.

These solvents should be residue-free, especially when used as a hand-wipe solvent or as a dip-tank degreasing solvent. Wash down the sides of the bomb shell with e156-09, using a wash bottle.

BoxArlingate Ln. Wet developer coatings can be removed effectively by water rinsing or water rinsing with detergent either by hand or with a mechanical assist scrub brushing, machine washing, etc. Solvent soaking 15 min minimumand ultrasonic solvent cleaning 3 min minimum techniques are recommended. Longer times may be necessary under some circumstances. It is the responsibility of the user of this standard to establish appropriate safety and e16509 practices and determine the applicability of regulatory limitations prior to use.

Release the pressure at a slow, uniform rate such that the operation requires not less than 1 min.

ASTM E – Standard Practice for Liquid Penetrant Examination for General Industry

A typical mixture is 2. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. The penetrant is usually red, so that resultant indications produce a de?

Acids and chromates can adversely affect the? Electrostatic spray application can eliminate excess liquid build-up of penetrant on the part, minimize overspray, and minimize the amount of e16-509 entering hollow-cored passages which might serve as penetrant reservoirs, causing severe bleedout problems during examination.

  JOHANSSON MIKROKATOR PDF

Water free of contaminants that could clog spray nozzles or leave a residue on the part s is recommended. This prerinse allows for the removal of excess surface penetrant from the parts prior to emulsi? This dullness should be removed by periodic polishing of the bomb.

Such treatments include, but are not limited to, vapor blasting, deburring, sanding, buffing, sandblasting, or lapping. Add mL of acetone. Determine separate blanks for both? If titration is manual, set the pH meter on the expanded millivolt scale and note the reading. Proceed to Checkout Continue Shopping. The cleaning properties of detergent solutions facilitate complete removal of soils and contamination from the surface and void areas, thus preparing them to absorb the penetrant.

As the voice of e165-90 U. SI units are provided for information only. Combining values from the two systems may result in nonconformance with the standard.

Unless otherwise indicated, it is intended that all reagents shall conform to the speci? Current edition e165-099 June 15, It will remove inorganic soils and many organic soils from the surface of parts, but may not reach to the bottom of deep discontinuities, and a subsequent solvent soak is recommended.

The anions of interest are separated on the basis of their relative affinities for a low capacity, strongly basic anion exchanger guard and separator column. It is recommended to not add oxygen or ignite the sample if the bomb has been jarred, dropped, or tilted.

For this purpose there must be a separate code, standard, or a speci?