ASTM D – Air Permeability of Textile Fabrics . ASTM E testing covers a pin-type bearing test of metallic materials in order to determine bearing yield. Find the most up-to-date version of ASTM E at Engineering ASTM E covers the standard test method for pin-type bearing test of metallic materials. The ultimate strength and yield strength of a bearing material are.
|Published (Last):||8 September 2007|
|PDF File Size:||3.31 Mb|
|ePub File Size:||10.65 Mb|
|Price:||Free* [*Free Regsitration Required]|
ASTM E238 – Pin Bearing Test of Metallics
This guide covers dynamic testing of vulcanized rubber and rubber-like both hereinafter termed “rubber” or “elastomeric” materials and products, leading from the definitions of terms used, through the basic mathematics This test standard covers the determination of the shear properties of high-modulus fiber-reinforced composite materials by clamping the ends of a V-notched specimen between two pairs of loading rails.
Determines tensile shear strengths of adhesives for bonding metals when tested in an essentially peel-free standard specimen that develops adhesive stress distribution representative of that developed in a typical low-peel While the test also lends itself to parallel-fiber reinforced These test standards cover procedures for testing untreated paper used w238 electrical insulating purposes.
This test standard covers the determination of the relative tensile strength of adhesives by the use of bar- and rod-shaped butt-joined specimens. This test covers the determination of the comparative shear strengths of adhesives for bonding metals when tested on a standard specimen and under specified conditions of preparation and testing at These test standards cover procedures for testing the static adhesional strength of rubber to rigid materials in most cases metals.
The test machine will grip one end of the plate test specimen, and the other end will grip the pin. This test standard ee238 the procedure for testing the tensile breaking strength of the perforations in one-part continuous forms. This test standard covers the determination ast, flexural properties of unreinforced and reinforced plastics, including high-modulus composites e23 electrical insulating materials in the form of rectangular bars molded directly or The test standard is useful for generating comparative shear strength data for joints made from a These test standards cover the determination of the adhesion strength between plies of fabric bonded with rubber or the adhesion of the rubber layer in articles made from rubber attached E2238 test standard determines the in-plane shear response of sstm matrix composite materials reinforced by high-modulus fibers.
Exova Toulouse laboratory gains Airbus authorisation for ASTM Bearing testing | Exova
This standard covers the shear properties of composite materials asstm by high-modulus fibers. This test standard covers the determination of puncture properties of rigid plastics over a range of test velocities. This standard covers the measurement of the tearing strength of textile fabrics by the tongue single rip procedure using a recording constant-rate-of-extension-type CRE machine. Adhesives to be used in laminate joints in nonstructural lumber products – interior and exterior mouldings, window and door components or parts, and bonded lumber panels.
This test standard e328 the determination of the comparative shear strength of adhesives for bonding metals when tested on a standard specimen and under specified conditions of preparation and testing This test porcedure covers the determination of the comparative tensile properties of the adhesive bonds of metal to metal when tested 2e38 standard shape specimens and under defined conditions of Bestimmung der Zugeigenschaften an senkrechten Kernverbunden.
This test standard covers the determination of elastic properties of “as produced” elastomeric yarns made from rubber, spandex or other elastomers.
This test standard is used to measure the grab tensile properties of reinforced geomembranes. This specification covers Penrose-type rubber tubes used in performing certain surgical drainage procedures. This test standard covers accelerated testing for tensile creep, and tensile creep-rupture properties using the Stepped Isothermal Standard. This test covers the measurement of tensile properties of natural and man-made single textile fibers of sufficient xstm to permit mounting test specimens in a tensile testing machine.
Elastic properties include force at specified elongations, permanent deformation This test standard covers the determination of the force required to disengage snap fasteners by a pull perpendicular to and parallel with aatm plane of the snap fastener.
This test standard covers the measurement of the resistance to delamination of the secondary backing applied to some pile yarn floor coverings. This test standard measures the e2338 strength of hook and loop touch CRE fasteners using a recording constant rate of extension tensile testing machine. These test cover procedures used to evaluate the tensile tension properties of vulcanized thermoset rubbers and thermoplastic elastomers.
Fixtures conform to ASTM – Grip-Engineering
These test covers the determination of properties of a pressure-sensitive adhesive. These test standards cover the procedures for testing copper-clad laminates produced from fiber-reinforced, thermosetting polymeric materials intended for fabrication of printed wiring boards. This standard describes a procedure and fixture used to determine shear strengths of adhesives used to bond materials with moduli higher than the modulus of the adhesive.
These test standards cover the determination of the creep and creep-rupture properties of plastic lumber and shapes, when loaded in compression or flexure.
This standard covers the measurement of the peel strength of hook and loop touch fasteners using a recording constant-rate-of-extension tensile testing machine CRE. These test standards cover the measurement of the breaking tenacity of manufactured textile fibers taken from filament yarns, staple, or tow fiber, either crimped or uncrimped, and tested in either This test covers the determination of fracture strength in cleavage of adhesives when tested on standard specimens and under specified conditions of preparation and testing.
The composite material forms are limited to continuous-fiber or discontinuous-fiber tape or This test standard covers strip test procedures for determining the tensile properties of Turf Reinforcement Mats.
These standards cover, but are not limited to, rubber-coated fabrics, that is, tarpaulins, rainwear, and similar products. Helps determine tensile and compressive creep r238 creep-rupture of plastics under environmental conditions. Standard Test Methods for Coated Fabrics.
ASTM E specifies the hole diameter and distance from the edge of the bearing material.
This standard describes the measurement for bursting strength with a ball burst strength tester of textiles or garments that exhibit a high degree of ultimate elongation. Structural panels in use include plywood, wafer board, oriented strand board, Procedures are specified for determining the damage resistance This test standard covers the determination of the force required to pull a steel cord from a wstm of vulcanized rubber. This test standard covers the determination of the tensile and tensile adhesion properties of rigid cellular materials in the form of test specimens.