Cardax FT Controller – Download as PDF File .pdf), Text File .txt) or read online. Installation Guide. Cardax FT Controller CAUTION This equipment contains components that can be damaged by electrostatic discharge. Ensure both you. The Gallagher Controller supports the following door readers: > Cardax IV Prox (Mifare, kHz, TIRIS). > Cardax IV Prox Plus (Mifare, kHz,. TIRIS).

Author: Mokus Moogulkree
Country: Rwanda
Language: English (Spanish)
Genre: Art
Published (Last): 3 April 2004
Pages: 308
PDF File Size: 19.63 Mb
ePub File Size: 20.21 Mb
ISBN: 191-1-60471-431-8
Downloads: 97744
Price: Free* [*Free Regsitration Required]
Uploader: Nijar

The Cardax FT Cabinet should be installed in a secure, internal location. The In-service relay is used to signal an external alarm if the Controller fails. In the event of a catastrophic failure, after approximately 60 seconds the In-Service relay opens.

Set switch 2 to ON closed. Carefully lift the Controller clear of the Cabinet.

Cardax Ft Controller pdf Download Report. Alternatively, an override reset on the Controller can be carried out in Cardax FT Command Centre via the Status and Overrides tab of the Controller properties with the cabinet closed. The Gallagher Controller R has on-board connections for with variations for the Gallagher Controller R shown in brackets:.

Unused For factory testing only. The software is powerful, Card readers Intruder Alarms may be installed in elevator cars to Documents.

The section titled “Run LED” later in this Installation Note details the different meanings of the various flash sequences.

  INTERPRETASI TES WIDAL PDF

High Spec variant only The High Spec variant of the Controller has a secondary Ethernet connection link to which communications can automatically be switched upon failure of the primary Ethernet connection. Revert to the factory default version of the operating system.

On startup, the main application is run. One GBUS port to cardaxx This means in the event of network communications being disrupted, security is maintained on site. The security of the installation ultimately depends on the way the Cardax FT Cabinet is installed.

Cardax Ft Controller 6000pdf

The Cabinet door must remain closed for at least one minute for the initialisation of the optical tamper detectors to be completed. There is a proprietary serial communication protocol between the two boards. The Gallagher Controller R has on-board connections for with variations for the Gallagher Controller R shown in brackets: Each device attached to a Cardax FT Controller must be allocated an “address”.

These contacts close when the Controller is powered up, and remain closed until either the power is removed or there is a ‘Catastrophic Failure’.

The Controller has dropped its code. Both units are designed to fit into a standard Cardax FT Cabinet together. Published on Oct View 1. Flash Slow Fast 1 flash 2 flashes Sequence timing Meaningms on, ms off Controller is searching for software FTS files ms on, ms off 4Hz flash ms on, ms off 1Hz flash 2 flashes – pause 600 flash is 50ms on, ms off, 1.

  CALLESELLA CATALOGO PDF

Shimano tiagra flight deck 9 speed manual Acer travelmate lci driver Ni circuit design suite keygen Documents. Looking at the Controller it will be obvious that the there is no ethernet activity on either ethernet connection, as the RJ45 connector LEDs will not be operating, and the Controllers run LED will be in 2 flash.

Turn on the power supply. Ensure that the power to the Cardax FT Controller is switched off and cwrdax. The following initialisation procedures are detailed in the later section titled “Initialisation”: On-board connections are provided for:.

On startup configuration and the IP address is deleted.

Cardax Ft Controller pdf

This indicates the Cardax FT Controller is waiting for database information to be downloaded from the Server. Cardax FT Version 5. The power supply cable must be of sufficient size to ensure that the voltage at the GBUS unit terminals is the recommended 12 Vdc.

Standard and High Specis a processing board for an intruder alarm and access control system. Following full antistatic precautions, disconnect all cables from the Cardax FT Controller On-board connections are provided for: This operation can only be reset by the factory of manufacture.