DISPERBYK® is a wetting and dispersing additive for solvent-borne systems . It is composed of a solution of a copolymer with acidic groups. This prod. Solution of a copolymer with acidic groups. Acts as a wetting and dispersing additive for aqueous and solvent-borne systems. Provides deflocculation through . Material Safety Data Sheet. DISPERBYK Version Revision Date 08/14/ Print Date 08/14/ 1 / SECTION 1. PRODUCT AND COMPANY.

Author: Zulkilkis Zulujinn
Country: Congo
Language: English (Spanish)
Genre: Spiritual
Published (Last): 11 September 2013
Pages: 411
PDF File Size: 17.13 Mb
ePub File Size: 3.5 Mb
ISBN: 559-5-24576-548-2
Downloads: 56666
Price: Free* [*Free Regsitration Required]
Uploader: Akir

If the conductive polymer is also the dispersant for metallic nanoparticles, the resistivity of the resulting metallic films may be significantly reduced, due at least in part to limited or no additional contamination from residual non-conducting dispersants.

Ink compositions involving near-infrared absorber dyes and use in ink jet printing devices. Surface preparation to eliminate whisker growth caused by plating process interruptions. Upon shearing such a system beyond a yield stress, it becomes liquid and thus flows easily.

DISPERBYK (KGS/DRUM) – Suka Chemicals

Polymeric dispersants may have higher viscosities than liquids used as vehicles in conductive inks. Thus, charging through proton gain or loss, or charging by adsorbed charges, may be involved in achieving a good dispersion. Conductive ink composition for inkjet printer, method for forming metal pattern by inkjet printing and printed cirsuit board using the method.

Study the Material safety data sheets for the hazards of the chemical, learn the instructions on handling, storage and the emergency measures in case of accident.

Are you a distributor who is interested in being listed here? Copper fine particle dispersion, a pattern forming method, and a manufacturing method of the copper pattern layer. In some implementations, polyacids, such as polystyrenesulfonic acid, may be used for charge compensation in an ink formulation. These differences may result from different surface energies of substrates, different adhesion properties of substrates, requirements of different printing methods such as ink-jetting, and different strategies used to sinter the metallic inks into metal conductors.


Positively charged nanoparticles may form an electrostatic dispersion with a dispersant containing both anionic and cationic polymer chains. You may choose a language below to continue to this industry or close this dialog above. These mechanical processes may be carried out in the presence of a dispersant to reduce the occurrence of re-agglomeration after mechanical agitation. Method of making electronic housings more reliable by preventing formation of metallic whiskers on the sheets used to fabricate them.

In some-cases, heat from photosintering causes a welding effect between the metal and plastics having relatively low melting points, yielding excellent adhesion between these metallic conductors or films and the substrate without the use of binder materials. The printed and dried inks may be cured.


Metal article coated with tin or tin alloy under tensile stress to inhibit whisker growth. TEGO Datasheet; http: Photovoltaic thin-film cell produced from metallic blend using high-temperature printing. In an implementation in which ionic polythiophene conducting disperbbyk are used to prepare aqueous metallic inks, the positive charge may be located within a polythiophene network.

Complete a full risk assessment for your workplace so that you can map out all the hazards into a single comprehensive COSHH assessment. Efficient and environmentally-friendly antibacterial and mildewproof inorganic composite nano-powder slurry and its preparation method.

The pre-cure step required at least 15 minutes to ensure that the water and solvents were removed, and that the resulting material was dry. Steric stabilization of metal nanoparticles may be achieved with a non-ionic dispersant or polymer.


Supply of DISPERBYK-110

Metallic nanoparticles may have an oxide layer on their surface. Another advantage of a high exclusion volume is that it allows for a low concentration of dispersant to be used, and therefore, only a small quantity of dispersant to be removed during the curing process.

Task management method, task management device, semiconductor integrated circuit, electronic apparatus, and task management system. The polymeric dispersant may be ionic, non-ionic, or any combination of ionic and non-ionic polymeric dispersants.

DISPERBYK® by Byk – Paint & Coatings

The following examples are provided to more fully illustrate some of the embodiments of the present invention. At low pH, the hydroxide surface may react with protons to produce a positively charged surface.

The maintenance of a dispersion may be assisted by mechanically breaking up the agglomerates with a ball mill or other device, sonication e.

Conducting polymers with multiple binding sites may partially surround a metal nanoparticle, thereby keeping it from aggregating or agglomerating. The nanoparticle may be, for example, copper. A conductive ink includes metallic nanoparticles, a polymeric dispersant, and a solvent. We’d love to send you exclusive offers and the latest info relating to health and safety and safety data sheets by email and other electronic means.

Method for synthesis of core-shell type and solid solution alloy type metallic nanoparticles via transmetalation reactions and applications of same. Year of fee payment: In some cases, the metallic surface may be heterogeneous, having both negatively and positively charged sites.