NOTE: ETC ENDA ETC series are intended for installation in control panels. Make sure that the device is used only for intended purpose. The shielding. Thank you for choosing ENDA EPC profile controller. * Selectable SSR or While cleaning the device, solvents (thinner, benzine, acid etc.) or corrosive. Double set point. Selectable sensor type (Pt, J, K, L, T, S, R). PID control function with accurate self-tuning. Digital inputs can be assigned to 3 different.

Author: Ker Faerg
Country: Mayotte
Language: English (Spanish)
Genre: Career
Published (Last): 4 February 2013
Pages: 407
PDF File Size: 4.4 Mb
ePub File Size: 1.52 Mb
ISBN: 944-5-59287-729-1
Downloads: 17473
Price: Free* [*Free Regsitration Required]
Uploader: Tukasa

Relative humidity According to EN Front panel: The normal value is 0. Pay attention to the polarities of the thermocouple cables as shown in the figure right are connected to the.

Technical Specification

Make sure that the device is used only for intended purpose. If no key is pressed within 20 seconds during programming mode, the data is stored automatically and the run mode is entered. Read this document carefully before using this device.

IfInp parameter is selected TC or Pt, etf parameter is seen. S different from out1.

Enda ETC Series PID Temperature Controllers Panel Mount | Rapid Online

While cleaning the device, solvents thinner, benzine, acid etc. Using this parameter the energy requirements of the system is adjusted at the set point. Then, the value is adjusted by using PV A1. During an installation, all of the cables that are connected to the device must be free of energy. If the temperature unit is changed, the value of the UPL. When PID parameters are Filter for display value.

  ACER P1273 PDF

Enda ETC Series PID Temperature Controllers Panel Mount

Before self tune procedure, A. If independent alarm is selected, A1.

Press any key to deactivate the self-tune procedure. If independent or deviation alarm is selected, this parameter can be Lo.

If deviation alarm is selected, A1. While holding 25 REdY. Before self tune procedure, temperature setpoint value should be adjusted. It enea be Adjusable between 1 and Adjustable between 1 and After PID is calculated A. If this parameter is adjusted to a value closer to the energy requirements of the system at the set point, process temperature is prevented to rise or drop to dangerous levels. After 1 second following the release of the key, initial condition is returned.

Four kinds of functions can be selected. Enter PID 940 of the system if they are known at the begining. The maximum value is the value of A1. Therefore, when using a grounding thermocouple, do not connect the logic output terminals to the ground.

The maximum value is the value of A2. If process value is Appropriate to begin self tune, rEdY. Then the device heats until setpoint etv according to PID parameters and calculates the energyrequirement for stable If the parameter is 31, the filter run most slow.

RS Modbus communication None Difference addresses should be selected for every device. If 0 is selected, soft start feature will be ettc and the device reaches set point value quickly.

  KAWASAAKI TD024D PDF

The maximum value is the value of C. The same procedure is valid for the decrement key. Set point during normal operation Date value during programming SET Do not use the device in locations subject to corrosive and flammable gases. It’s a community-based project endz helps to repair anything. UnIt Offset value is added to the measurement value. Adjustable between 1 and seconds. Adjustable between 0 and minutes. The device must be protected against inadmissible humidity, vibrations, severe soiling and make sure that the operation temperature is not exceeded.

If self tune is achieved A. 94420 logic control output.

The maximum of C. These cables should not be close to the power cables or components. SEt is the value of C. If this parameter is set to 0, the output power becomes 0 at the set point.

All input and output lines that are not connected to the supply network must be laid out as shielded and twisted cables. If the selected input type is changed, the value of C. The shielding must be grounded on the instrument side.