Interplater hd85 thermal pdf. Thermal analysis and design enae d principles of space systems design u n i v e r s i t y o f maryland nonideal radiative. Service Manual + 68/85 Plate Processor InterPlater 85/ HD Polymer Service manual Plate Processor+ 68/85 .. Cleaning of developer heating element. Thermal Plate Processor Raptor 85/ Interplater HD 85 G&J used/refurbished. Glunz Jensen Interplater Plate Processor Model Perfect Condition.

Author: Yozshutilar Kigashura
Country: Panama
Language: English (Spanish)
Genre: Business
Published (Last): 25 September 2008
Pages: 461
PDF File Size: 15.93 Mb
ePub File Size: 1.51 Mb
ISBN: 377-8-28134-890-8
Downloads: 86987
Price: Free* [*Free Regsitration Required]
Uploader: Mejin

Mount the exit table.

InterPlater 85/135 HD Thermal

Mount red, yellow and brown wire in terminal 1. As shown in the figure below the hose must be connected between the water tap and the water inlet solenoid valve located to the left, when standing in front of the processor, underneath the processor. Installation kit Installation- and spareparts kits are included with the rhermal. The interplaher has been either off or in sleep mode for more than 72 hours. In the wash section the plate is washed on both sides by means of the spray tubes 13 and brushed on the upper side by means of the brush 14 optional.

Move the exit guide a little upwards and mount the 4 screws in the lower holes of the guide 6.

The filter s are placed underneath the processor in the right side and mounted in a drawer unit for easy access. They comprise the different parts necessary to make the installation and some key components as spareparts. Set developer brush speed according to recommendations from the plate manufacturer.

  JOSEPH FRANZ VON ALLIOLI PDF

Rewire if necessary accordingly to table below. A-8 Sensors and control interplatdr. A-6 Low voltage wiring. The rollers 7 at the section exit squeeze any residual water off the plate. Characteristics of thermal interface materials 4 apparent thermal conductivity it is a common practice to calculate an apparent or therjal thermal conductivity from a single measurement of thermal impedance z at one thickness t of a particular interface material.

Check with the chemicals supplier for details.

Transport security items During transportation many of the parts outside and inside the processor have been secured using tape, plastic, strips, and various pieces of sponge rubber. X3,B to F10,5 Orange: Do not rely on the floor being absolutely in level.

The parameters to be configured are: Make sure to remove all items. Install the rollers as shown on the label. Developer The processor is equipped with a fill-up pump for developer. When performing any service, maintenance, calibration, or trouble shooting etc.

A-4 24V DC distribution. If straight position B is wanted please follow the description for B. If this does not help, take the pump apart and clean both of the small valves in warm water. Recycling The processor should be disposed at a certified appliance recycling centre or processing centre. A-6 V AC control devices. Conduction direct transfer by contact of solid, liquid or gas.

Installation and adjustment of brush rollers are described in chapter 3 in the processor service interplafer. X3,D to F10,1 Blue: Spare parts and service period: Please refer to the Software Manual “Control Panel Service Guide” for detailed information of the procedures listed in the following. Mount the spray tubes 4.

  CIRCUIT ANALYSIS DEMYSTIFIED BY DAVID MCMAHON PDF

Installing level sensor kit requires configuration of replenishment parameters in the software. When installation of the setter interface is complete please return to this manual for finishing the entire installation by continueing with the instructions on the next page. The brush adjustment can vary from one processor to another since it must apply to the specific plate and chemical type etc.

The gum solution from the application tube 20 forms a small bath between these two rollers and a thin layer of finisher is applied to the plate while the extra finisher is forced backwards.

Products | Glunz & Jensen

Special recommendations As some chemicals may require special cleaning agents, contact your chemicals supplier for recommendations about cleaning agents for your processor. If the processor has low level by starting up, or goes low level during production, pump will be activated from Manual mode in the Tool box. Solar thermal energy an industry report solar thermal technology on an industrial scale the sun is our source our sun produces ,,,, watts of energy every second and the belief is that it will last for another 5 billion years.

Batteries No batteries in this equipment. X3,F to F10,1 Black: