Gauging of hexagon sockets (ISO ); German version EN ISO ISO Gauging of hexagon sockets. standard by International Organization for Standardization, 01/15/ View all product details. Buy NF EN ISO Gauging Of Hexagon Sockets from SAI Global.

Author: Tukazahn Akinora
Country: Belgium
Language: English (Spanish)
Genre: Photos
Published (Last): 18 October 2014
Pages: 246
PDF File Size: 6.4 Mb
ePub File Size: 10.42 Mb
ISBN: 881-8-20567-287-4
Downloads: 5712
Price: Free* [*Free Regsitration Required]
Uploader: Vokinos

Every care has been taken to ensure that the file is suitable 233429 use by ISO member bodies. In addition, when full-size screws are loaded using the type of testing fixture illustrated in ISOthey shall withstand, without fracture, the minimum ultimate tensile loads given in Table 3. A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status izo the official versions.

In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

Sprawdzian gniazd sześciokątnych PN-EN ISO – Google Books

Up-to-date lists and bibliographical references concerning such national standards may be isi on application to the Central Secretariat or to any CEN member. For dated references, only the edition cited applies. Symbols and designations of dimensions are defined in ISO ISO shall not be held responsible for identifying any or all such patent rights. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s member body in the country of the requester.


Hexagon socket button head screw ISO – M12 40 – The work of preparing International Standards is normally carried out through ISO technical committees. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. In accordance with Adobe’s licensing policy, this file may uso printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing.

If, in special cases, specifications other than those listed in this International Standard are required, they should be selected from existing International Standards, e. Requirements for non-electrolytically applied zinc flake coatings are covered in ISO Details of the software products used to create this PDF 234229 can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Adobe is a trademark of Adobe Systems Incorporated.

NOTE Particular attention is drawn to the note in Isk 2 and to Table 3 concerning the limitation on ultimate tensile load. All rights reserved; No part of this publication may be reproduced or utilized in any form or by any means — elec- tronic, mechanical, photocopying or any other data carriers without prior permission from ON!

Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee.


In downloading this file, parties accept therein the responsibility of not infringing Adobe’s licensing policy. Intermediate nominal lengths according to ISO are permissible.

BS EN ISO 23429:2004

This third edition cancels and replaces the second edition ISO Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by Julyand conflicting national standards shall be withdrawn at kso latest by July Endorsement notice The text of ISO Table 3 — Minimum ultimate tensile loads for hexagon socket button head screws of the values specified in ISO Thread Property class 8.

Alternative form of socket permissible For broached sockets which are at the maximum limit of isk the overcut resulting from drilling shall not exceed of the length of any flat of the socket which is. They shall nevertheless meet the other material and property requirements for the respective property class specified in ISO The main task of technical committees is to prepare International Standards.

Acceptability Acceptance procedure is covered in ISO Technical Committee Mechanical fasteners Publisher and printing: For undated references, the latest edition of the referenced document including any amendments applies.